OFFLINE REPLAY - not a new PPC512 execution or screenshot
Decoded by the 0.3-dev host build on 22 October 2026.
Input: ROM/shared-prefix capture and full configuration capture from
21 October 2026, before the NIC IRQ5 change. Their common 256 bytes match.
These were separate reads, not an atomic capture of all live BIOS variables.
IRQ3 below is historical; the last hardware network test used IRQ5.

Command: pmcfg-host --details -f captured-details.bin

PicoMEM configuration 0.3-dev  |  ELKS  |  READ ONLY [FILE]
ROM D000:0000  BIOS 2026-06-16  Shared D000:4000  ID 12
Layout: 768-byte profile, board 11 / BIOS 2026-06-16
Init: SD OK [00]  WiFi OK [00]  USB OK [00]
Config init: OK [00]  PSRAM code: 08  HW IRQ: 7
NE2000: enabled  port 0x300  IRQ 3  WiFi enable flag: 0
ELKS bootopts candidate: ne0=3,0x300,,0x92 (verify IRQ routing)
Hardware IRQ mask: 0xA8  NIC IRQ direct: available
RAM extension: SRAM on  PSRAM off  Max conventional on
EMS: port 0x268  frame E000h  USB on  Joystick off
Configured map: each character = 16 KiB, from 00000h to FFFFFh
ssssssssssssssssssssssssssssssssrrrrrrrrrrrrrrvv....BB..eeeeoooo
s=PC RAM r=card RAM p=PSRAM e=EMS v=video B=BIOS o=PC ROM .=none
Configured disks (names, not filesystem mount status):
  FDD0 -                  0 KB  PC/off (attr 00)
  FDD1 -                  0 KB  PC/off (attr 01)
  HDD0 hd64-minix        63 MB  image (attr 80)
  HDD1 -                  0 MB  PC/off (attr 01)
  HDD2 -                  0 MB  PC/off (attr 02)
  HDD3 -                  0 MB  PC/off (attr 03)
Boot disk index: 0  Fast boot off  Card bootstrap on
Snapshot only: no firmware commands, port I/O or config changes.

Board and BIOS variables (sampled; not live ELKS driver status):
  Board ID: 11  Pico ID: 0
  Firmware revision: not reported (zero)
  BIOS starts: 4  Bootstraps: 4  Base port init: OK [00]
  BIOS disk counts: HDD 0 -> 1  FDD 2 -> 2
  BIOS PC memory: 512 KB  Tandy mode: 0  RAM blocks: 0
  Command sample: 00  Source: 00  SPI PSRAM flag: 0
  USB device bits: 00 (unused; not a device inventory)

Configured option ROMs (not proof of activation):
  ROM0 -              size 0 KB  blocks 0 x 16 KB
       address byte 00 -> segment 0000:0000 (no blocks assigned)
  ROM1 -              size 0 KB  blocks 0 x 16 KB
       address byte 00 -> segment 0000:0000 (no blocks assigned)

Additional configured settings:
  Ignore A/B segments: off  BIOS SRAM limit: 16 x 16 KB
  BIOS ROM limit: 0 x 16 KB  Setup before boot: off
  BIOS boot flag: 0  SD clock: 24 MHz  RAM clock: 100 MHz
  RTC: off (0x2C0-0x2C7)  Menu colour profile: 0

Configured audio (not an audio probe):
  Rendering: on  AdLib: on (0x388-0x389)
  Tandy        off  configured port 0x0000
  CMS          off  configured port 0x0000
  SoundBlaster off  configured port 0x0000
  Mindscape    off  configured port 0x0000
  SoundBlaster IRQ: 0 (only relevant when enabled)
  Other audio bytes: 00 00 00 00 00

Extended image settings (names/paths, not mount status):
  CD-ROM: -  stored size word: 0
  FDD0 directory:
    (empty)
  FDD1 directory:
    (empty)
  HDD0 directory:
    (empty)
  HDD1 directory:
    (empty)
  HDD2 directory:
    (empty)
  HDD3 directory:
    (empty)
